Yamaha EK40G Service Manual Download

Page: 192 / 200

TRBL

SHTG

9-5

6H95G11

Troubleshooting

Symptom: The engine idle speed does not remain steady.

Check the operation of the
carburetor.

Check the throttle cable and link
operation.

Yes

Adjust the throttle cable and
throttle link.

Yes

Check the ignition system chart.

Adjust the pilot screw according
to specifications.

Yes

Using compressed air, clean the
pilot screw, needle valve, main
and pilot jets, and main nozzle.
Replace any damaged parts.

Is the
carburetor operat-
ing correctly?

Are they operat-
ing correctly?

Check the pilot screw.

Yes

Is the pilot screw
setting correct?

Disassemble the carburetor and
check the internal parts.

Check the throttle valve for
smooth operation.

Are the fuel or
air passages
clogged?

Yes

Correct or replace the carburetor.

Does the throttle
valve stick?

Check the ignition system or
compression system. Replace
if foulty parts.

6H95G11_09 04.7.5 11:53 Page 6

Summary of Contents for EK40G









































































































































































































Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands

Yamaha EK40G, Service Manual

Search results

Summary of Contents for EK40G

Reviews:

Related manuals for EK40G

Brands by name

Popular brands