manualshive.com logo in svg

Xylem WEDECO SMOevo PLUS Series, Original Manual, Page: 66 / 179

Share
Download
Xylem WEDECO SMOevo PLUS Series Original Manual Download Page 66

 

Manual Ozone Generating System 

SMOevo

PLUS

 

Transport and Storage 

 

Manual_SMOevoPLUS_eng_01.2019.doc 

page 66 of 179 

 

 

6  Transport and Storage 

This section describes the safety measures, the requirements for the personnel and the 
procedures with regard to transport, packaging and storage of the ozone system. 

6.1  Safety during Transport and Storage 

6.1.1 Safety Instructions  

 

 

 

WARNING! 

 

  Hazard due to falling loads! 

Risk of serious injury or death. 

 

•

 

Only use lifting aids and slings permitted to the total weight. 

•

 

Never stand under suspended loads. 

•

 

Secure the ozone system against tilting. 

•

 

Make sure that nobody stands under suspended loads. 

•

 

Secure the hazard area against unauthorized access. 

 

 

 

NOTICE! 

 

Contamination by dust, shavings and similar from mild steel (C 
steel) or scratches! 

Risk of corrosion of stainless steel (CrNi steel) components. 

 

•

 

Make sure that stainless steel parts are properly covered prior 
to transportation to the actual installation or storage place. 

 

 

 

NOTICE! 

 

Vibration of the ozone generator! 

Risk of breakage of electrodes. 

•

 

Keep the ozone generator away from any possible vibration 
sources.  

 

 

Summary of Contents for WEDECO SMOevo PLUS Series




















































































































































































Reviews:

No comments