Xylem WEDECO SMOevo PLUS Series Original Manual Download Page 47 | Manualshive

Page: 47 / 179

Xylem WEDECO SMOevo PLUS Series Original Manual Download Page 47

Manual Ozone Generating System

SMOevo

PLUS

System Description

Manual_SMOevoPLUS_eng_01.2019.doc

page 47 of 179

5.3.1 Subassembly 01: Gas Supply

01.1.30

Ball valve

Gas supply is carried out via a ball valve which must be
fully open during normal operation.

01.1.35

Fine filter

Prevents particles >0.1 µm from entering and damaging
the generator and the valves.

01.1.40

Pressure
regulator

Keeps the operation pressure constant if feed gas
pressure varies within a certain range.

03.1.03

Ball valve

Can be used for the option Ozone Monitor (M1).

01.1.50

Safety
Pressure
Limiter
Combination

Two pressure limiters with integrated pressure transmitter.

Via the analog signal of the pressure transmitter, the PLC
receives the current pressure in the gas inlet. Warning and
switch-off points for exceeding or falling below certain
pressures are stored in the PLC. When the shutdown
points are reached, the system will be switched off via the
PLC.
A message is displayed when the warning points are
reached.

Pressure

Gas Inlet

Description*

Delay

Time

≥3.0 bar (g)

Max. switch-off point

warning message disappears

alarm message appears

→ after 1 sec: system shuts down

1 s

2.7 bar (g)

Max. warning value

≥ 2 .7 bar(g) and < 3 bar(g)

warning message appears after 5 sec

< 2.7 bar(g) warning message disappears

5 s

«
...
45
46
47
48
49
...
»

Summary of Contents for WEDECO SMOevo PLUS Series




















































































































































































Reviews:

No comments