Xtore NASolution NP1040 User Manual Download Page 36

Page: 36 / 186

NFP Storage Manager 1.1 User’s Manual

Chapter 4. Using NFP Storage Manager 1.1

different subnet, thus when choosing network type through
DHCP please make sure if the subnet has any DHCP server

available to use.

Please use a switch with “Trunking/Fail-over” support to make
sure the “Trunking/Fail-over” feature can be fully supported by

NASolution NP1040

Date Setup

System administrator can change the time, date and time zone of
N

P1040

NAS server. Please refer to

Server Configuration

Basic

Server Configuration

Enter the system date and time

unit of Chapter

3 for ways to setup.

Summary of Contents for NASolution NP1040



























































































































































































Search results

Summary of Contents for NASolution NP1040

Reviews:

Related manuals for NASolution NP1040

Brands by name

Popular brands

Xtore NASolution NP1040, User Manual

Search results

Summary of Contents for NASolution NP1040

Reviews:

Related manuals for NASolution NP1040

Brands by name

Popular brands