Xtore NASolution NP1040 User Manual Download Page 142

Page: 142 / 186

NFP Storage Manager 1.1 User’s Manual

Troubleshooting

137

and save it as “net$log.dat”.

map p:=\\NAS001_nw\public1

write login_name

if login_name<>"SUPERVISOR" and

login_name<>"SUPERVIS" and login_name<>"GUEST" then

map h:=\\NAS001_nw\home

end

As shown in the example, the login script will map the

public1

folder on

NAS001

as “p” drive and map users’ home folders on

NAS001

as “h” drive for all Novell clients on the LAN.

Save the “net$log.dat” file to the

\SYS\PUBLIC folder

NP1040

NAS server.

Problems about Apple Clients’ Access to NP1040

NAS Server

Cannot find NP1040 NAS server via Chooser or Network

Browser.

Make sure

NP1040

NAS server has been turned on and

connected to the LAN.

Check if the Apple client is able to connect with other AppleTalk

servers. If not, the network settings of this Apple client are

incorrect.

Make sure system administrator has enabled Apple networking

connections over AppleTalk or TCP/IP protocol.

Summary of Contents for NASolution NP1040



























































































































































































Search results

Summary of Contents for NASolution NP1040

Reviews:

Related manuals for NASolution NP1040

Brands by name

Popular brands

Xtore NASolution NP1040, User Manual

Search results

Summary of Contents for NASolution NP1040

Reviews:

Related manuals for NASolution NP1040

Brands by name

Popular brands