Xtore NASolution NP1040 User Manual Download Page 24

Page: 24 / 186

NFP Storage Manager 1.1 User’s Manual

Chapter 3. Quick Configuration

TIP

The domain name field does not accept the following characters. If
you are using a DHCP server, do not use these characters on the
DHCP server either:

(, ), <, >, @, \, [, ], , , ;, :, “, space, enter (/n) and control characters.

LAN Port

Next, please setup the IP address of the first network port. This
page will show the setup information previously defined in

NFP Setup

Assistant

, and system administrator can make additional changes

here.

If your LAN includes a DHCP server, click

Get network configuration

through DHCP

. Otherwise, choose

Use manual configuration

. Filling

out the column with a “red star sign” on the right is mandatory, while
filling out the column with the “orange star” is recommend by the
system.

Your NP1040 NAS server supports two network ports. You must go to

Server Configuration

Basic Configuration

after completion of

Quick

Configuration

to continue setup of other network port.

Summary of Contents for NASolution NP1040



























































































































































































Search results

Summary of Contents for NASolution NP1040

Reviews:

Related manuals for NASolution NP1040

Brands by name

Popular brands

Xtore NASolution NP1040, User Manual

Search results

Summary of Contents for NASolution NP1040

Reviews:

Related manuals for NASolution NP1040

Brands by name

Popular brands