file:///C|/Documents%20and%20Settings/Miz%20B/My%...GTA/Nuvera%209.0%20UGTA_FINAL/English/spec_41.htm (1 of 4)8/13/2008 4:44:25 PM
Basic Finishing Module (BFM/BFM Plus) Specifications
The BFM is a finisher that provides high capacity collecting, stacking and stapling. It also includes a top tray for collecting or purging
sheets. The Xerox Nuvera System offers two BFM models:
Using the BFM
Go to
Using the Basic Finishing Module
for information on how to use the BFM and all of the adjustments that affect the BFM.
Capacities
Stacker
Top Tray
Stapler
Specifications
●
The
BFM
is a finisher that provides high capacity collating, stacking and stapling. It also includes a top tray for collecting or
purging sheets.
●
The
BFM Plus
is comprised of the Bypass BFM and the Interface Module. The BFM Plus module provides the same
capabilities as the BFM. However, it does not have a top tray and does include a bypass paper path that allows the BFM Plus
to pass pages through an Interface Module (IM) to another BFM or through an Interface Module and Finishing Transport
Module to other DFA-compliant finishers.
●
The
BFM Plus Top Tray with Direct Connect
is comprised of the Bypass BFM with an Interface Module that has Top Tray
capabilities and is able to connect directly to a DFA-compliant finisher(s). The DFA-compliant finishers are limited to devices
that have an 860mm height, Center registration, and a velocity of 1130mm/s.
●
3,000 sheets total capacity of 20 lb. (75-80 gsm) paper or equivalent.
●
The stack limit can be set from the UI for each BFM independently.
●
Stapled sets with <15 sheets are limited to 100 sets.
●
It can staple up to 100 sheets of 8.5 x 11 inch or A4 LEF, and 8.5 x 14 inch or B4 SEF of 20 lb. (75-80 gsm). Portrait,
landscape, and dual position stapling are available
●
The Stacker is the output tray for receiving compiled stapled and unstapled sets as well as single sheets. Output is normally
delivered with side-1 down and sets can be offset.
●
250 sheets of 20 lb. (75-80 gsm) paper or equivalent.
●
Output to the Top Tray is delivered with Side-1 down and sets are not offset.
●
It can be set as a destination tray for non-stapled jobs.
●
Sheets less than 7 inches in the process direction or 8 inches in the cross-process direction will automatically go to the Top
Tray. The Top Tray also receives sheets that are purged from the system.
●
Paper size greater than 18.5" in the process length will run to the top tray only.
●
The Basic Finishing Module has two internal pass-through 100 sheet up side down staplers. The stapler devices have the
ability to portrait, landscape or dual staple all paper sizes between 5.5"x8.5"; / A5 and 12.6"x18.5". Finished sets can be
stacked internally to the lower stacker tray.
●
These staplers have the capability of stapling 100 sheets of 20lb. (75-80 gsm) or equivalent substrates (reduced stapled sheet
capabilities can result based on substrate properties (i. e. thickness, density, material, coating, etc.).
●
If either of the Staplers runs out of staples see
Replacing Staples
or if it jams see
Clearing Staple Jams
.
●
An alternate Staple Cartridge is available with 30 sheets of 20lb. (75-80 gsm) paper capacity.
Contact Xerox
for information on
ordering refills.
●
Each Stapler Cartridge holds 5000 staples.
Contact Xerox
for information on ordering refills.
Home
|
Resources
|
Search
|
Index
|
|
System Tour
|
|
Maintenance
Problem Solving
About this Site
178 of 256
