Woxcon MUH44T-H2 User Manual Download | Manualshive

Page: 58 / 66

background image

4x4 HDMI 2.0 HDBaseT Matrix Switcher

53

Command

Description

Command Example and
Response

STA_HDCP.

Report the HDCP mode of all outputs.

OUT 01 HDCP BYPASS!
OUT 02 HDCP BYPASS!
OUT 03 HDCP BYPASS!
OUT 04 HDCP BYPASS!
OUT 05 HDCP BYPASS!
OUT 06 HDCP BYPASS!
OUT 07 HDCP BYPASS!
OUT 08 HDCP BYPASS!

8.3.5 EDID Management

Command

Description

Command Example and
Response

EDIDMInit.

Reset factory default EDID to all input ports.

All Input EDID Set Default!

EDIDUpgrade[XX].

Upgrade the EDID data of the input port [XX].
[XX]=00~04, U.
[XX]=00, represents all inputs.
[XX]=01~04, represents HDMI input 1~4.
[XX]=U, upload a user-defined EDID. The
EDID can be saved for invoking at any time.
When the command applied, system prompts
to upload the EDID file (.bin). Operation will
be cancelled in 10 seconds. Please
disconnect HDBT connection before sending
command to ensure the data can be received
successfully.

EDIDUpgrade01.

EDIDUpgradeU.

256
9600bps
Input XX/User Define EDID
Upgrade OK By RS232 Or
GUI!

EDID/[XX]/[YY].

EDID/03/01.

«
...
56
57
58
59
60
...
»

Summary of Contents for MUH44T-H2



































































Reviews:

No comments

Related manuals for MUH44T-H2

RackSwitch G8264T

Brand: IBM Pages: 20

Xbox One Media Hub

Brand: Collective Minds Pages: 19

Brand: FS Pages: 41

Brand: HIKVISION Pages: 5

ExtremeSwitching SLX 9540

Brand: Extreme Networks Pages: 108

Brand: TP-Link Pages: 28

QuantaMesh T4000 Series

Brand: QCT Pages: 41

KingShield T206-C

Brand: Green Brook Pages: 2

Brand: I-Tech Pages: 123

Brand: Bticino Pages: 2

Brand: A-Neuvideo Pages: 20

Master View CS-172

Brand: ATEN Pages: 1

Brand: Wyrestorm Pages: 4

Brand: Grizzly Pages: 2

Brand: Keysight Technologies Pages: 75

Brand: NETGEAR Pages: 2

PoE Giga-MiniMc

Brand: IMC Networks Pages: 28

GoControl WA00Z-1

Brand: Nortek Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands