Woxcon MUH44T-H2 User Manual Download

Page: 9 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

Output Load Capability

L+R:

1KΩ and higher (Supports 10x paralleled 10KΩ loads).

Stereo Channel Separation

>70dB@1KHz.

Noise Level

L+R:

-80dB;

SPDIF:

-90dB

Control Part

Control port

(4) IR IN, (1) IR ALL IN, (4) IR OUT, (1) IR ALL OUT, (1) IR EYE,
(5) RS232, (1) FIRWARE, (1) TCP/IP

Control Connector

(11) 3.5mm jacks, (5) 3-pin terminal blocks, (1) Type-A USB, (1)
RJ45

General

Transmission Mode

HDBaseT

Transmission Distance

1080p ≤ 230 feet (70 meters),
4K@60Hz ≤ 131 feet (40 meters)

Bandwidth

18Gbps

Operation Temperature

-5

℃

~ +55

℃

Storage Temperature

-25

℃

~ +70

℃

Relative Humidity

10% ~ 90%

External Power Supply

100V~240V AC, 50/60Hz

Power Consumption

65W (Max)

Dimension (W*H*D)

436.4mm x 44mm x 356.6mm

Net Weight

3.3kg

2.2 HDBaseT Receiver

Video

Input

(1) HDBT

Input Connector

(1) RJ45

Input Resolution

Up to 4Kx2K@60Hz 4:2:0

Output

(1) HDMI

Output Connector

(1) Type-A female HDMI

Output Resolution

Up to 4Kx2K@60Hz 4:4:4 8bit, HDR10

Audio

Input

(1) ARC Audio In

Input Connector

(1) Toslink Connector

Output

(1) Audio Breakout

Output Connector

(1) Toslink connector

Audio Format

Supports PCM, Dolby Digital, Dolby True-HD, DTS and DTS-HD.

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands