Woxcon MUH44T-H2 User Manual Download

Page: 48 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

8.3 RS232 Commands

When controlling the matrix, the serial port settings for all RS232 commands is:

Baud rate: 9600

Data bit: 8

Stop bit: 1

Parity bit: none

The matrix switcher can be controlled by sending the following RS232
commands:

8.3.1 System Setting

Command

Description

Command Example and
Feedback

PowerON.

Power on the system.

Power ON!

PowerOFF.

Power off the system.

Power OFF!

/*Name.

Report product name.

MUH44T-H2

/*Type.

Report product model.

HDBaseT Matrix

/^Version.

Report software version.

V1.0.0
CPLD:V1.0.0
VideoDriverVersion:V1.0.0

RST.

Reset to factory default.

Factory Default!

Lock.

Lock front panel buttons.

Front Panel Locked!

Unlock.

Unlock front panel buttons.

Front Panel UnLock!

GetGuiIP.

Report the GUI IP.

GUI_IP:192.168.0.178!

SetGuiIP:xxx.xxx.xx
x.xxx.

Set the GUI IP to xxx.xxx.xxx.xxx.

SetGuiIP:192.168.0.176.

SetGuiIP:192.168.0.176!

Baudrate115200.

Set the serial baud rate of matrix switcher to
115200.

Set Local RS232 Baudrate
Is 115200!

Baudrate57600.

Set the serial baud rate of matrix switcher to
57600.

Set Local RS232 Baudrate
Is 57600!

Baudrate38400.

Set the serial baud rate of matrix switcher to
38400.

Set Local RS232 Baudrate
Is 38400!

Baudrate19200.

Set the serial baud rate of matrix switcher to
19200

Set Local RS232 Baudrate
Is 19200!

Baudrate9600.

Set the serial baud rate of matrix switcher to
9600.

Set Local RS232 Baudrate
Is 9600!

PHDBTON.

Enable PoC of HDBT outputs for powering
HDBaseT receivers.

HDBT Power ON!

PHDBTOFF.

Disable PoC of HDBT outputs.

HDBT Power OFF!

STA_PHDBT.

Report the PoC status of HDBT outputs.

HDBT Power ON!

DS[XX]ON.

DS00ON.

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands