Woxcon MUH44T-H2 User Manual Download

Page: 44 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

8.1.2 Control the Matrix Switcher from Remote

To control the matrix switcher from remote location, please connect one or more PCs
to the

RS232

ports of HDBaseT receivers with the

3-pin to DB9 RS232 Cables

. The

matrix switcher can be controlled by any one of PCs, the connection diagram is
shown as below:

Note:

The command “

RS232RCM[XX]ON.

” (

[XX]

00~04

) needs to be sent to enable

or disable this control mode. For example, send the command “

RS232RCM00ON.

” to

enable the remote-control mode for all HDBaseT outputs, and send the command
“

RS232RCM00OFF.

” to disable the remote-control mode for all HDBaseT outputs.

Please refer to the 8.3.1 System Control for more details.

AUDIO MATRIX OUT / ARC

IR EYE

LINK

HDCP

Display

Receiver

LINK

HDCP

Display

Receiver

4K Blu-Ray

HDMI:

RS232:

HDBaseT:

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands