Woxcon MUH44T-H2 User Manual Download

Page: 52 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

Command

Description

Command Example and
Feedback

Front Panel UnLock!
Local RS232 Baudrate Is
9600!
GUI_IP:192.168.0.178!
Output 01 Switch To In 01!
……

STA_IN.

Report the connection status of all HDMI input
ports.

IN 1 2 3 4
LINK N N N Y

STA_OUT.

Report the connection status of all HDMI and
HDBT outputs.

OUT    1    2    3    4    5    6
7    8
LINK N    N    N    Y    N    N
N    N

8.3.2 Signal Switching

Command

Description

Command Example and
Response

IRFVON.

Enable the IR switching to follow the video
switching.

IR Follow Video ON!

IRFVOFF.

Disable the IR switching to follow the video
switching.

IR Follow Video OFF!

OUT[XX]:[YY].

Switch video input [YY] to video output [XX].
[XX]=00~04, [YY]=01~04. The “[XX]=00”
represents all outputs.

OUT01:04.

Output 01 Switch To In 04!

STA_VIDEO.

Report the input channel for all outputs.

Output 01 Switch To In 01!
Output 02 Switch To In 02!
Output 03 Switch To In 03!
Output 04 Switch To In 04!

IR[XX]:[YY].

Switch far-end IR IN [YY] to local IR OUT
[XX]. [XX]=01~04, [YY]=00~04. The “[YY]=00”
represents all far-end IR IN ports.

IR01:03.

Local 01 IR Out Switch To
Remote 03 IR IN!

STA_IR.

Report IR switching status.

IR Follow Video ON!
Local 01 IR Out Switch To
Remote 01 IR IN!
Local 02 IR Out Switch To
Remote 02 IR IN!

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands