Woxcon MUH44T-H2 User Manual Download

Page: 18 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

To copy the EDID data from one HDMI output to one or several inputs:

Example: Input 1 and 2 learn the EDID data of HDMI output 4.

Select

Learn HDMI OUT

Press

to confirm.

Press

OUTPUT 4

Press

INPUT 1

and

Press

to confirm.

To invoke the built-in EDID data:

There are six types of built-in EDID data can be invoked, as shown as below:

No.

EDID

Video

Audio

1080p

2CH

1080p HDR

MultiCH

4K@30Hz HDR

2CH

4K@60Hz HDR

MultiCH

5 (Default)

4K@60Hz HDR

2CH

4K@60Hz HDR

MultiCH

User Custom

Example: Input 1 and 2 invoke the built-in EDID data: 4K@30Hz HDR 2CH.

Select

Built-in EDID

Press

to confirm.

Press

navigation buttons to select the

built-in EDID to be invoked

Press

INPUT 1

and

Learn HDBT OUT
Learn HDMI OUT <

PRESS INPUT KEY

Learn HDMI OUT 1

PRESS INPUT KEY

Learn HDMI OUT 4

1 2
Learn HDMI OUT 4

Learn HDMI OUT
Built-in EDID <

PRESS INPUT KEY

1080P 2CH <

PRESS INPUT KEY

4K30HDR 2CH <

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands