Woxcon MUH44T-H2 User Manual Download

Page: 17 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

5.4 EDID Management

The Extended Display Identification Data (EDID) is used by the source device to match
its video resolution with the connected display. By default, the four source devices
invoke the fifth built-in EDID: 4K@60Hz HDR 2CH.

Enter EDID management tab:

Press

to select

EDID Management

Press

enter EDID management tab.

Press

navigation buttons to select the below items:

Learn HDBT OUT

Learn HDMI OUT

Built-in EDID

To copy the EDID data from one HDBT output to one or several inputs:

Example: Input 1, 2, 3 and 4 learn the EDID data of HDBT output 2.

Select

Learn HDBT OUT

Press

to confirm.

Press

OUTPUT 2

Press

INPUT 1

Press

to confirm.

Status Info
EDID Management <

Learn HDBT OUT <
Learn HDMI OUT

PRESS INPUT KEY

Learn HDBT OUT 1

PRESS INPUT KEY

Learn HDBT OUT 2

1 2 3 4
Learn HDBT OUT 2

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands