Woxcon MUH44T-H2 User Manual Download

Page: 13 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

3.3 Receiver Front and Rear Panel

①

Power LED:

The LED illuminates red when power is applied.

②

ARC Mode:

Press the button with paper clip or other sharp tool to enable the ARC

mode, and then the left LED illuminates blue. Press it again to exit the ARC mode

and the LED is off. When the ARC audio is selected as the audio source for the

SPDIF output of matrix switcher, the ARC mode will be enabled automatically.

③

ARC Audio In:

Toslink connector to connect ARC audio source device (e.g.TV).

④

FW:

Micro-USB port for firmware upgrade.

⑤

HDMI Out:

Type-A female HDMI output port to connect HDMI display (e.g.TV).

⑥

Audio Breakout:

If the ARC mode is OFF, the Toslink connector is connected to

speaker or amplifier for HDMI source audio de-embedding. Note that if the ARC

mode is ON, this port has no audio output.

⑦

IR In:

3.5mm jack to connect the IR receiver for IR pass-through.

⑧

IR Out:

3.5mm jack to connect the IR emitter for IR pass-through.

⑨

RS232:

3-pin terminal block to connect the RS232 control device (e.g. PC) or a

third-party device to be controlled.

⑩

HDBT In:

RJ45 port to connect the HDBT output port of switcher/transmitter by

CATx Ethernet cable. The LINK LED illuminates orange when there is a valid

HDBaseT link between the switcher/transmitter and the receiver. The HDCP LED

illuminates green when the video contains HDCP content.

⑪

DC 24V:

DC connector for the power adapter connection. If the

switcher/transmitter is connected to the power adaptor, the receiver doesn’t need

to connect power adaptor due to the HDBT output port of switcher/transmitter

supports 24V PoC output.

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands