Woxcon MUH44T-H2 User Manual Download

Page: 49 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

Command

Description

Command Example and
Feedback

Enable the video resolution down-scaling
function of HDMI output [XX]. [XX]=00~04. The
“[XX]=00” represents all HDMI outputs.

HDMI OUT 01 Down Scale
ON!
HDMI OUT 02 Down Scale
ON!
HDMI OUT 03 Down Scale
ON!
HDMI OUT 04 Down Scale
ON!

DS[XX]OFF.

Disable the video resolution down-scaling
function of HDMI output [XX]. [XX]=00~04. The
“[XX]=00” represents all HDMI outputs.

DS00OFF.

HDMI OUT 01 Down Scale
OFF!
HDMI OUT 02 Down Scale
OFF!
HDMI OUT 03 Down Scale
OFF!
HDMI OUT 04 Down Scale
OFF!

STA_DS.

Report the down-scaling function of HDMI
outputs.

HDMI OUT 01 Down Scale
OFF!
HDMI OUT 02 Down Scale
OFF!
HDMI OUT 03 Down Scale
OFF!
HDMI OUT 04 Down Scale
OFF!

RS232RCM[XX]ON.

Enable the RS232 remote-control mode for
HDBT output [XX] that the matrix switcher can
be controlled from remote PC. [XX]=00~04.
The “[XX]=00” represents all HDBT outputs.

RS232RCM00ON.

RS232 Remote 01 Control
MCU ON!
RS232 Remote 02 Control
MCU ON!
RS232 Remote 03 Control
MCU ON!
RS232 Remote 04 Control
MCU ON!

RS232RCM[XX]OFF.

Disable the RS232 remote-control mode for
HDBT output [XX] that the matrix switcher
cannot be controlled from remote PC.

RS232RCM00OFF.

RS232 Remote 01 Control
MCU OFF!

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands