Woxcon MUH44T-H2 User Manual Download

Page: 59 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

Command

Description

Command Example and
Response

The input [XX] recall the embedded EDID
[YY]. [XX]=00~04. The “00” represents all
inputs.
[YY]=01~07.

[YY]

EDID

1080p 2CH

1080p MultiCH

4K@30Hz HDR 2CH

4K@30Hz HDR MultiCH

4K@60Hz HDR 2CH

4K@60Hz HDR MultiCH

User-defined EDID

Input 03 EDID Upgrade OK
By 01 Internal EDID!

EDIDGOUT[XX].

Report the EDID data from output [XX].
[XX]=01~08.
[XX]=01~04, represents HDBT output 1~4.
[XX]=05~08, represents HDMI output 1~4.

EDIDGOUT04.

EDIDOUT04:
……

EDIDM[XX]B[YY].

Copy the EDID data of output [XX] to input
[YY].
[XX]=01~08, [YY]=00~04.
[XX]=01~04, represents HDBT output 1~4.
[XX]=05~08, represents HDMI output 1~4.
[YY]=00, represents all inputs.
[YY]=01~04, represents HDMI input 1~4.

EDIDM04B01.

Input 01 EDID Upgrade OK
By 04 EXT EDID!

EDIDSTA[XX].

Report the EDID status of input [XX].
[XX]=00~04.
[XX]=00, represents all inputs.
[XX]=01~04, represents HDMI input 1~4.

EDIDSTA00.

Input 01 EDID From 01
Internal EDID!
Input 02 EDID From 01
Internal EDID!
Input 03 EDID From 01
Internal EDID!
Input 04 EDID From 01
Internal EDID!

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands