Woxcon MUH44T-H2 User Manual Download

Page: 62 / 66

4x4 HDMI 2.0 HDBaseT Matrix Switcher

Control the input source:

Command

Description

Command Example and

Response

CECI[AA][BB][CC]00.

Confirm operation (Enter).

CECI02044400

CEC Input 02 Send Success!

CECI[AA][BB][CC]01.

UP direction.

CECI01044401.

CEC Input 01 Send Success!

CECI[AA][BB][CC]02.

DOWN direction.

CECI01044402.

CEC Input 01 Send Success!

CECI[AA][BB][CC]03.

LEFT direction.

CECI03044403.

CEC Input 03 Send Success!

CECI[AA][BB][CC]04.

RIGHT direction.

CECI03044404.

CEC Input 03 Send Success!

CECI[AA][BB][CC]09.

Back to submenu.

CECI03044409.

CEC Input 03 Send Success!

CECI[AA][BB][CC]0A.

Enter main menu.

CECI0304440A.

CEC Input 03 Send Success!

CECI[AA][BB][CC]0D.

Exit menu.

CECI0204440D.

CEC Input 02 Send Success!

CECI[AA][BB][CC]6D.

Power on.

CECI0204446D.

CEC Input 02 Send Success!

CECI[AA][BB][CC]6C.

Power off.

CECI0204446C.

CEC Input 02 Send Success!

Control the output display device:

Command

Description

Command Example and

Response

CECO[AA][BB][CC]41.

Volume up.

CECO05404441.

CEC Output 05 Send Success!

CECO[AA][BB][CC]42.

Volume down.

CECO05404442.

CEC Output 05 Send Success!

CECO[AA][BB][CC]43.

Mute

CECO05404443.

CEC Output 05 Send Success!

CECO[AA][BB]04.

Power on.

CECO038004.

CEC Output 03 Send Success!

CECO[AA][BB]36.

Power off.

CECO038036.

CEC Output 03 Send Success!

Summary of Contents for MUH44T-H2


































































Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands

Woxcon MUH44T-H2, User Manual

Search results

Summary of Contents for MUH44T-H2

Reviews:

Related manuals for MUH44T-H2

Brands by name

Popular brands