background image

INSTALLATION AND OPERATION MANUAL 

CNGE2FE8MSPOE2

MANAGED ETHERNET SWITCH WITH (8) 10/100 BASE-TX  

+ (2) 10/100/1000 BASE-TX/FX COMBO PORTS  

AND POWER OVER ETHERNET (POE)

The ComNet

  CNGE2FE8MSPOE2 is a hardened Managed Ethernet Switch. It 

provides IEEE 802.3af (15W) PoE to eight 10/100BASE-T(X) ports and has two-
gigabit combination SFP or RJ-45 ports. Up to 120 watts of PoE power is available 
for distribution across all 8 TX ports. All SFP ports utilize ComNet SFP* modules for 
fiber and connector type and distance. The CNGE2FE8MSPOE2 is a redundant switch 
offering multiple Ethernet redundancy protocols, C-Ring (recovery time <10ms over 
250 units of connection), ComRing, and MSTP/RSTP/STP (IEEE 802.1 s/w/D). This 
redundancy feature protects your applications from network interruptions or temporary 
malfunctions by redirecting transmission within the network. Network management 
is supported by eConsole, a powerful, easy-to-use Windows-based utility, as well as 
Web-based telnet, and Console (CLI) configurations. This environmentally hardened 
switch is designed for direct deployment in difficult out-of-plant or roadside operating 
environments.

Rev. 4.23.14

Summary of Contents for CNGE2FE8MSPOE2










































































































Reviews: