manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 65

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

© Woodward 

Page 65/79 

Password 

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

 

 

 

NOTE

 

Once the code level is entered, access to the configuration menus will be allowed for two hours or until 
another password is entered into the control. If a user needs to exit a code level then code level CS0 
should be entered. This will block any configuration of the control. A user may return to CS0 by allow-
ing the entered password to expire after two hours or by changing any one digit on the random num-
ber generated on the password screen and entering it into the unit.

 

 
 

Define level 1 
code        0000 

Code level 1 (Operator) 

0000 to 9999 

This code level entitles the user to change selected parameters. Changing a pass-
word is not permitted at this level. This password expires two hours after entering 
the password and the user is returned to the CS0 level. For more information on 
password protection refer to page 39. 

 

Define level 2 
code        0000 

Code level 2 (Commissioner) 

0000 to 9999 

This screen appears only in code level 2 (password protection enabled). The code 
number entered here in this screen permits direct access to all parameters (display-
ing and changing). In addition, the user may also set the password for levels CL1 
and CL2. This password expires two hours after entering the password and the user 
is returned to the CL0 level. For more information on password protection refer to 
page 39. 

 
 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands