manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 35

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

© Woodward 

Page 35/79 

 

6

 

f- 

Color: yellow 

Governor output decrease frequency 

 

 

Three position controller 

The LED "f-" indicates if the control outputs a pulse to decrease the fre-
quency. The status of the LED corresponds to the status of the relay "speed 
lower". 
 

 

Analog controller 

If the actuator output signal of the controller is changing to reduce the fre-
quency, the LED illuminates. 

 

7

 

f+ 

Color: yellow 

Governor output increase frequency 

 

 

Three position controller 

The LED "f+" indicates if the control outputs a pulse to increase the fre-
quency. The status of the LED corresponds to the status of the relay "speed 
raise"." 
 

 

Analog controller r 

If the actuator output signal of the controller is changing to increase the fre-
quency, the LED illuminates. 

 

8

 

V- 

Color: yellow 

Governor output reduce voltage 

 

 

Three-position controller 

The LED "V-" indicates if the control outputs a pulse to decrease voltage. 
The status of the LED corresponds to the status of the relay "voltage lower". 
 

 

Analog controller 

If the actuator output signal of the controller is changing to reduce the volt-
age, the LED illuminates. 

 

9

 

V+ 

Color: yellow 

Governor output increase voltage 

 

 

Three-position controller 

The LED "V+" indicates if the control outputs a pulse to increase 
voltage. The status of the LED corresponds to the status of the relay 
"voltage raise". 
 

 

Analog controller r 

If the actuator signal of the controller is changing to increase the 
voltage, the LED illuminates. 

 

10

 

Gen CB - ON 

Color: green 

Power circuit breaker ON 

The LED "Gen CB - ON" signals the response of the generator cir-
cuit breaker. The LED illuminates if the discrete input "Reply: CB is 
open" is not energized and will extinguish as soon as the discrete in-
put is energized. (see also chapter "LED "Gen CB - ON" Flashes" on 
page 27). 

 

11

 

Bus CB – ON

 

here: non-functional 

Color: green 

Mains power circuit breaker ON 

NOTE

: This LED is non-functional, as this is a "One-power-circuit-

breaker configuration". 

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands