manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 26

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

Page 26/79 

© Woodward 

Mains Parallel Operation 

In mains parallel operation both circuit breakers are closed and the real power and the power factor cos phi are 
controlled to the configured set point values, provided that the controllers are configured to enabled. If the pa-
rameter "terminal 6 = Release control" is set, terminal 6 must also be energized, so that the controllers operate. 

Selection of the power set point value 

•

  If the generator is connected in parallel with the mains via the CB, initially a partial load is assumed. 

•

  When the partial load pre-run is completed (or deactivated) the following table is valid for the selection of the 

power set point mode:  

 

Parameter 
"Terminal 6" 

Condition 

"Terminal 6" 

Parameter 

"Power set point ex-

ternal" 

active set point value 

ON 

External: via 0 to 20 mA 

Release control 

x 

OFF 

Internal: Power controller Pset2 

ON 

External: via 0 to 20 mA 

1 

OFF 

Internal: Power controller Pset2 

Set point power 

0 

x 

Internal: Power controller Pset1 

0: "OFF"  / 1: "ON"  / x: Signal of no significance (0 or 1) 

Table 4-4: Power set point modes 

•

  If an external signal has been selected for the parameter "Power set point external", the correct signal type 

must be selected on the following configuration screen. 

•

  The power set point upper limit must be configured as the value "Power controller P max" 

•

  The power set point lower limit must be configured as the value "Power controller P min" 

•

  The power set point has a configurable ramp rate. This slope can be configured in the parameter "Power c

troller Ramp". 

on-

 

Shutdown 

If the parameter "Download and open GCB" has been configured as "ON", the controller can be configured to 
perform a shutdown function in the following manner: 

•

  Terminal 3 "Enable CB" is re-energized, initiating the shutdown 

•

  The power will be reduced 

•

  When the real power falls below 10 % of the generator rated power, the relay "Command: open CB" will 

open  

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands