manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 6

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

Page 6/79 

© Woodward 

Chapter 1. 

General Information 

 

The SPM-D11 is a synchronizing unit with integrated control functions for generator power levels and load shar-
ing. Through the application of appropriate logic to the discrete inputs the following functions can be realized: 
 

•

 Synchronization, 

•

 Synch-check, 

•

 Black 

start, 

•

  Load/var control and 

•

 Load/var 

sharing. 

 
Type designation of the SPM-D comprises a standard control plus options as follows: 
 

SPM-D11 

4 

5 -h0018 B/ 

-ABDEF..Z

   

 

 

   

 

 

 

 

 

 

   

 

 

 

 

 

 

   

 

 

 

 

Options

 according to list of options. 

These options can be found in this manual. Each chapter headline 
points out if the described function is standard or has to be ordered as 
an option. 

 

   

 

 

 

 

Mounting 

[B]..Flush-mounting 
[M]..DIN-rail/rear panel mounting 

 

   

 

   

 

 

Hardware variation 

non-standard versions; e. g. green display, different relays 

 

   

 

   

 

 

Current transformers, secondary 

[1] = ../1 A 
[5] = ../5 A 

 

   

 

   

 

 

Voltage transformer, secondary 

[1] = 100 Vac (Range 50-120 Vac 
[4] = 400 Vac (Range 50-400 Vac) 

 

   

 

   

 

 

Type 

 
Examples: 

•

 SPM-D1145B/LSR (LSR package with 50-400 Vac voltage and ../5 A current measuring inputs) 

•

 SPM-D1111B/LSXR (LSXR package with 50-120 Vac voltage and ../1 A current measuring inputs) 

 

Intended Use

 The control must only be operated for the uses described in this manual. The prerequisite for a 

proper and safe operation of the product is correct transportation, storage and installation, as well as careful op-
eration and maintenance. 
 
 

 

NOTE

 

This manual has been developed for a control fitted with all available options. Inputs/outputs, func-
tions, configuration screens and other details described, which do not exist on your control, may be 
ignored. 
The present manual has been prepared to enable the installation and commissioning of the control. 
Due to the large variety of parameter settings, it is not possible to cover every combination. The man-
ual is therefore only a guide. In case of incorrect entries or a total loss of functions, the default settings 
can be taken from the list of parameters located in the rear of this manual. 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands