manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 56

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

Page 56/79 

© Woodward 

Load/Var Sharing 

 

Active power 

Load-share  ON   

Load sharing  

ON/OFF 

ON

................Real power is distributed among the generators operating in parallel. 

The generator outputs are distributed depending on the set values. 
The following screens of this function are displayed 

OFF

..............There is no load sharing control performed, and the following 

screens of this function are not displayed. 

 

Act. load share 

Factor     =00% 

Load sharing reference variable 

10 to 99 % 

The higher the weighing factor is configured, the more influence the main control 
variable (frequency) has on the control. The lower the weighing factor is config-
ured, the greater the influence of the secondary control variable (generator real 
power). 

 

Reactive power 

Load-share  ON   

var sharing 

ON/OFF 

ON

................Re-active power is distributed among the several generators operat-

ing in parallel. The generator outputs are distributed depending on 
the set values. The following screens of this function are displayed: 

OFF

..............There is no var sharing control performed, and the following screens 

of this function are not displayed

.

 

 

React.load share 

Factor     =00% 

var sharing reference variable 

10 to 99 % 

The higher the weighing factor is configured, the more influence the main control 
variable (voltage) has on the control. The lower the weighing factor is configured, 
the greater the influence of the secondary control variable (generator reactive 
power). 

 
 
 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands