manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 57

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

© Woodward 

Page 57/79 

Synchronization 

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

 

Functions of Synchronization 

 

Synchronizing 
functions   ON 

Synchronization functions 

ON/OFF 

ON

................ Frequency and voltage matching for the generator and busbar is per-

formed and a close command is issued. The subsequent screens of 
this function are displayed. 

OFF

.............. No synchronization occurs, but no-load control functions are per-

formed if necessary. No close command is issued. The subsequent 
screens of this function are not displayed. 

 

Synchronization 
 df max = 0.00Hz 

Max. permissible differential frequency (positive slip) 

0.02 to 0.49 Hz 

The prerequisite for initiating a close command that the differential frequency must 
be lower than the value configured here. This value specifies the upper frequency 
limit. A positive value indicates that the generator frequency is greater than the 
busbar frequency. 

 

Synchronization 
 df min =-0.00Hz 

Max. permissible differential frequency (negative slip) 

0.00 to

 

0.49 Hz 

The prerequisite for initiating a close command that the differential frequency must 
be higher than the value configured here. This value specifies the lower frequency 
limit. A negative value indicates that the generator frequency is less than the busbar 
frequency. 

 

Synchronization 
 dV max  =  00V 

Max. permissible differential voltage 

[1] 1 to 20 V, [4] 1 to 60 V 

A close command will not be issued until the measured differential voltage of the 
generator and busbar falls below the value configured here. 

 

Synchronization 
Brk.hold T>0.00s 

Minimum pulse period of close relay 

0.04 to 0.50 s 

The length of the close command pulse can be adjusted to the requirement of the 
subordinate switching circuit. 

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands