manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 43

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

© Woodward 

Page 43/79 

Controller 

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

 

 
Entering the values in the subsequent screens will change the parameters of the controller. 
 
 

 

CAUTION

 

Incorrect entries may lead to wrong measuring values and result in damage to the generator! 

 

Idle Control 

Automatic idle  
Running      ON 

Automatic no-load control 

ON/OFF 

ON

................ With the generator power circuit breaker open, frequency and volt-

age are controlled to the adjusted set point values in spite of the con-
troller not being enabled (see also chapter "Function" on page 20). 

OFF

.............. No-load control is carried out only with controller enabled (see also 

chapter "Function" on page 20). 

 

Terminal 6     
---------------- 

Function of terminal 6 

Release control / Set point power 

Release control

 The controller is enabled via the discrete input on terminal 6. The 

power circuit breaker is enabled separately via terminal 3 (Enable 
CB). Changing the set point value is not possible. 

Set point power: 

The power set point value is changed by energizing terminal 6. 

Enabling of the controller occurs along with enabling of the power 
circuit breaker via terminal 3 (Enable CB). 

 

Frequency Controller 

The SPM-D11/LSR is equipped with a three-position controller for frequency and does not contain the following 
screens. Only the screens for setting the three-position controller are available. With the extended version SPM-
D 11/LSXR, several controller output signals can be selected via the screens, which are listed by the controller 
model. 
 

f control type   
        -------- 

SPM-D11/LSXR only 

Frequency controller type THREE-STEP/ANALOG/PWM 

THREE-STEP

 The frequency controller operates as three-step controller and is-

sues raise (f+) and lower (f-) pulses via the configured relays. Only 
one of the two controllers (the frequency or the voltage controller) 
can be used for relay output at a time. 

ANALOG

.... The frequency controller operates as a continuous controller with an 

analog output signal (mA or V). 

PWM

........... The frequency controller operates as a continuous controller with a 

pulse-width-modulated output signal and constant level. 

 

Note

: The controller setting and the following screens differ, depending on which 

type of controller is selected here. 

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands