manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 48

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

Page 48/79 

© Woodward 

 

Volt. controller 
Dead band= 00,0V 

only SPM-D11/LSR and 

SPM-D11/LSXR 'THREE-STEP' 

Voltage controller insensitivity 

[1] 0.1 to 15.V, [4] 0.5 to 60.0 V 

No load/Isolated operation: 

The measured generator voltage is controlled so that 

it does not deviate from the configured voltage by more than the 
value configured in this dead band setting while operating in a steady 
state. 

Synchronization: 

The measured generator voltage is controlled so that the differ-

ential voltage does not exceed this dead band setting while operating 
in a steady state. The mains or busbar voltage is used as the set point 
value. 

 

Volt. controller 
Time pulse>000ms 

only SPM-D11/LSR and 

SPM-D11/LSXR 'THREE-STEP' 

Minimum voltage controller ON period 

20 to 250 ms 

The minimum ON period of the relay should be selected in such a manner that the 
downstream control element responds reliably to the pulse length that has been set 
here. The smallest possible time must be set in order to ensure optimum control be-
havior. 

 

Volt. controller 
Gain Kp     00.0 

only SPM-D11/LSR and 

SPM-D11/LSXR 'THREE-STEP' 

Voltage controller gain factor 

0.1 to 99.9 

The gain factor K

p

 influences the ON time of the relays. The gain factor Kp influ-

ences the ON time of the relays. By increasing the gain, the response is increased to 
permit larger corrections to the variable to be controlled resulting in longer ON 
time periods. The optimum setting depends on the behavior of the system. If the 
gain is too low, the control action becomes slow. If the gain is configured too high, 
the result is excessive overshoot/undershoot of the desired value. 

Analog Controller Outputs (SPM-D11/LSXR, Setting 'ANALOG') 

V control output 
         ------- 

SPM-D11/LSXR 

'ANALOG' 

Controller output signal 

see table 

The range of the analog output signal is adjusted here. To choose between a current 
signal in mA or a voltage signal in V, the appropriate jumpers must be connected to 
the output terminals. (see chapter Relay Outputs on page 16). 
The following output signals are possible: 

 

 

 

 

 

 

Type 

Setting in above c
figuration screen 

on-

Jumper 
between  
terminal 8/9 

Adjustment 
range 

Adjustment 
range  
min. 

Adjustment 
range 
max. 

Current 

+/-20mA (+/-10V) 

no 

+/-20mA 

-20 mA 

+20 mA 

 

+/-10mA (+/-5V) 

 

+/-10mA 

-10 mA 

+10 mA 

 

0 to 10mA (0 to 5V) 

 

0 to 10mA 

0 mA 

10 mA 

 

0 to 20mA (0 to 10V) 

 

0 to 20mA 

0 mA 

20 mA 

 

4 to 20mA 

 

4 to 20mA 

4 mA 

20 mA 

 

10 to 0mA (5 to 0V) 

 

10 to 0mA 

10 mA 

0 mA 

 

20 to 0mA (10 to 0V) 

 

20 to -0mA

20 mA 

0 mA 

 

20 to 4mA 

 

20 to 4mA 

20 mA 

4 mA 

Voltage 

+/-20mA (+/-10V) 

yes 

+/-10V 

-10 Vdc 

+10 Vdc 

 

+/-10mA (+/-5V) 

 

+/-5V 

-5 Vdc 

+5 Vdc 

 

+/-3V 

 

+/-3V 

-3 Vdc 

+3 Vdc 

 +/-2.5V 

 

+/-2,5V 

-2,5Vdc 

+2,5 

Vdc 

 

+/-1V 

 

+/-1V 

-1 Vdc 

+1 Vdc 

 

0 to 10mA (0 to 5V) 

 

0-5V 

0 Vdc 

5 Vdc 

 

0.5V to 4.5V 

 

0,5 to 4,5V

0,5 Vdc 

4,5 Vdc 

 

0 to 20mA (0 to 10V) 

 

0 to 10V 

0 Vdc 

10 Vdc 

 

10 to 0mA (5 to 0V) 

 

5 to 0V 

5 Vdc 

0 Vdc 

 

4.5V to -0.5V 

 

4,5 to 0,5V

4,5 Vdc 

0,5 Vdc 

 

20 to 0mA (10 to 0V) 

 

10 to 0V 

10 Vdc 

0 Vdc 

 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands