manualshive.com logo in svg

Woodward SPM-D11, Manual

Share
Download
Woodward SPM-D11 Manual Download Page 39

Manual 37259C 

SPM-D11 - Synchronizing Unit 

 

 

 

 

© Woodward 

Page 39/79 

Password Protection 

The control is equipped with a three-level code and configuration hierarchy, which enables it to project various 
configuration screens for different categories of users. A distinction is made between: 
 

•

  Code level 0 (CL0) - 

User: Third party 

The user assigned this code level may view the monitored values but is prohibited from accessing any pa-
rameters. All configuration operations are blocked. 

 

•

  Code level 1 (CL1) - 

User: Operator 

This code level entitles the user to change selected parameters. Changing a password is not permitted at this 
level. This password expires two hours after entering the password and the user is returned to the CL0 level. 

 

•

  Code level 2 (CL2) - 

User: Commissioning personnel 

Allows direct access to all parameters (displaying and changing). In addition, the user may also set the pass-
word for levels CL1 and CL2. This password expires two hours after entering the password and the user is re-
turned to the CL0 level. 

 

Enter code 
            XXXX 

Enter code number 

0-9999 

Upon enabling the configuration mode, the user is required to enter an access code 
number, which identifies the various users. The displayed number XXXX is a ran-
domly generated number (RN). If the random number is confirmed by pressing the 
"Select" button without being changed, the current level of access is maintained. 
Upon entering either a level 1 or level 2 access code the corresponding level of ac-
cess is granted. If an incorrect access code is entered the control unit changes to 
code level 0 and all access is blocked until a code level 1 or 2 access code is en-
tered. 

 
 

 

NOTE

 

Two hours after entering a code level 1/2 access number, the code level automatically returns to CL0! 
The default code number for code level 1 (CL1) is "0001"! 
The default code number for code level 2 (CL2) is "0002"! 
The password protection can only be disabled in code level 2! 

 
 

Password 
Protection    ON 

Password protection 

ON/OFF 

ON

................ Access to configuration is achieved by entering the correct code 

number (code level 1/2). If a wrong code number is entered, the con-
figuration will be blocked. 

OFF

.............. The user has direct access to all parameters, the code number is not 

requested. 

 
 

Summary of Contents for SPM-D11
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands