Wincor Nixdorf TH180 Programmer'S Manual Download Page 77

Page: 77 / 162

TH180 Programmer’s Guide

(10) The following commands enable specification of any print start position for a

raster bit image.

a. Horizontal tab (HT)

b. Specify an absolute position (ESC $)
c. Specify a relative position (ESC \)

d. Set left margin command (GS L)

(11) Position arrangement (ESC a) is also applicable to a raster bit image.

(12) If this command has been executed during macro definition, the macro

definition processing is stopped, and processing by this command is started. In
this case, the macro is not defined.

(13) d indicates defined data.

The bit corresponding to a dot to be printed is set at "1," while the bit
corresponding to a dot to be not printed is set at "0."

(14) The following gives relationships between a raster bit image and printed data.

d64

d65

d66

d128

MSB

LSB

(xL + xH×256)×8 = 512 dots

(yL+yH×256) dots

(xL+xH×256)= 64 d ots

Summary of Contents for TH180



































































































































































Search results

Summary of Contents for TH180

Reviews:

Related manuals for TH180

Brands by name

Popular brands

Wincor Nixdorf TH180, Programmer'S Manual

Search results

Summary of Contents for TH180

Reviews:

Related manuals for TH180

Brands by name

Popular brands