Wincor Nixdorf TH180 Programmer'S Manual Download Page 50

Page: 50 / 162

TH180 Programmer’s Guide

GS B n

[Designation] Turn white/black reverse printing mode on/off

[Format]

1DH, 42H, n

[Valid limits] 0 n 255

[Initial value] n = 0

[Function] (1) Turns reverse printing mode on/off.

(2) The table below lists the bit definitions:

Bit

Function

Value

White/black reverse
printing

Cancel

Specify

To be defined

7 To be defined

(3) For parameter n, only the lowest-order bit is valid.

(4) Internal characters and user-defined characters are subject to reverse printing.

(5) The spacing on the right side of characters specified using the Set right-side

character spacing command (ESC SP) are also subject to reverse printing.

(6) This command does not affect the spaces between lines.

(7) The reverse printing specification has priority over the underline specification.

Therefore, even if underlining is specified, underlines will not be added for

characters for which reverse printing has been specified. The underline status

is not changed.

(8) This command is also applicable to external kanji characters.

Summary of Contents for TH180



































































































































































Search results

Summary of Contents for TH180

Reviews:

Related manuals for TH180

Brands by name

Popular brands

Wincor Nixdorf TH180, Programmer'S Manual

Search results

Summary of Contents for TH180

Reviews:

Related manuals for TH180

Brands by name

Popular brands