Wildlife Acoustics sm3bat User Manual Download Page 79

Page: 79 / 86

SM3BAT User Guide

Firmware Release Notes

page

BIOACOUSTIC MONITORING SYSTEMS

Firmware Release Notes

1.2.7

■

Improved the interpretation of programs containing non-infinite loops.

■

Further improvements to compatibility with certain SD cards.

1.2.5

■

Differentiate between "DIRTY" and "ERROR" cards. A card marked "DIRTY"

indicates that a critical write operation affecting the file system (typically at

the very beginning or ending of a recording) was interrupted due to an

unrecoverable error or power failure. The Song Meter SM3 will avoid

further use of a "DIRTY" card to avoid further card corruption that could

lead to unrecoverable data loss. Prior to 1.2.5, a "DIRTY" card was indicated

on the LCD as "ERROR" indistinct from other flash card problems. The

"DIRTY" condition can be cleared by accessing (writing) the card on your

host computer or by reformatting the card using the SM3 on-board

formatting utility.

■

Improvements to how cards are utilized. Files will now be written more

sequentially to cards A through D. Prior to this release, files and sensor log

entries were distributed more randomly across cards.

■

Further improvements to back-to-back triggering reducing turn-around

time.

■

Advanced feature: Added support for 32-bit recording. This feature is

specific to certain marine recording applications and is not intended for

general use. It only works for acoustic rates (not ultrasonic rates), trigger

level must be set to OFF (no triggers), and the recording channel must be

set to zero (mono recording on channel zero only). This mode is enabled

using the FEATURE program command.

1.2.1

■

Added automatic upgrade of boot code. Version A-1 will be updated to A-

3 to fix potential intermittent reliability issues.

■

Improved handling of ambiguous

AT_TIME

AT_SRIS

AT_SSET

commands. Recording will now begin immediately, if appropriate, as if the

program was started 24 hours previously. This behavior generally is more

likely to match the user’s intention and maximize recording time.

■

Improved accuracy of the

DMIN

and

DMAX

calculations.

■

Improved SD card compatibility.

■

Changed built-in programs to have

DMAX

set to

OFF

(infinity).

■

Program

AUTO

settings are now applied at record time rather than

program start time to improve fault tolerance and reduce risk of human

error.

Summary of Contents for sm3bat























































































Search results

Summary of Contents for sm3bat

Reviews:

Related manuals for sm3bat

Brands by name

Popular brands

Wildlife Acoustics sm3bat, User Manual

Search results

Summary of Contents for sm3bat

Reviews:

Related manuals for sm3bat

Brands by name

Popular brands