Wildlife Acoustics sm3bat User Manual Download Page 50

Page: 50 / 86

Developing Custom Programs

SM3BAT User Guide

page

BIOACOUSTIC MONITORING SYSTEMS

This command is only relevant if

TRGLVL

is not

OFF

See

DMIN

for more information on how the scrubber uses this value.

See

TRGLVL

for more information on how the trigger uses this value.

DMIN <dur-channel-0> <dur-channel-1>

Specifies the minimum duration for a signal in the specified frequency range

to be a valid signal to satisfy the scrubber Values are 0.1 – 800.0 msec in 0.1-

msec steps, or

OFF

The scrubber automatically deletes files where no suitable bat echolocation

is detected. The scrubber looks for at least two narrow band signals of at

least this

DMIN

duration and shorter than

DMAX

and within the frequency

range specified by

FRQMIN

and

FRQMAX

. If

two such signals exist, the file

is saved, if they are not, the file is not saved. 1.5ms is recommended for

recording bats.
If

TRGLVL

is not

OFF

, the files are scrubbed based on this field and

DMAX

If you do not want to scrub files, set this command and

DMAX

OFF.

DMAX <dur-channel-0> <dur-channel-1>

Specifies the maximum duration for a signal in the specified frequency

range to be a valid signal to satisfy the scrubber. Values are 0.1 msec – 800.0

msec in 0.1-msec steps, or

OFF

is recommended for recording bats.

The shortest

DMAX

chosen between channel 0 and 1 will also truncate the

total length of a WAV while recording on stereo channels. This means that if

one channel is in mid trigger and has not yet reached its

DMAX

and the

other channel does reach

DMAX

, the first channel will be truncated shorter

than its programmed

DMAX

See

DMIN

for more information on how the scrubber uses this value.

TRGLVL <level-channel-0> <level-channel-1>

Specifies the digital trigger level. Thresholds are either absolute (negative

values) or relative to the measured noise floor (positive values). The range is

-88 dB

–

+88 dB in 1-dB steps or

OFF

AUTO

selection is available.

If either channel value is not

OFF

, then the

FRQMIN, FRQMAX, DMIN,

DMAX, TRGWIN, and TRGMAX

commands are required before the next

RECORD

command.

The trigger is satisfied if a signal exceeds the specified level within the

frequency range defined by

FRQMIN

and

FRQMAX

Turning on triggers will also activate file scrubbing. For information on

scrubber function and how to turn off the feature, see

DMIN

Summary of Contents for sm3bat























































































Search results

Summary of Contents for sm3bat

Reviews:

Related manuals for sm3bat

Brands by name

Popular brands

Wildlife Acoustics sm3bat, User Manual

Search results

Summary of Contents for sm3bat

Reviews:

Related manuals for sm3bat

Brands by name

Popular brands