Wildlife Acoustics sm3bat User Manual Download Page 13

Page: 13 / 86

SM3BAT User Guide

SM3BAT Overview

page

BIOACOUSTIC MONITORING SYSTEMS

Channel 0 Microphone Connector: Connect an SMM-U1 ultrasonic microphone,

SMM-A1 acoustic microphone, or SM3-H1 hydrophone.

Channel 1 Microphone Connector: Connect an SMM-U1 ultrasonic microphone,

SMM-A1 acoustic microphone, or SM3-H1 hydrophone.

Serial Communication Connector: For the optional GPS time-synch receiver or

the available Song Stream remote access hardware.

External Power Cable and Audio Output Connector: Use for external batteries

(with or without solar panels).

All batteries, memory cards, LCD display, and electronic controls are mounted

inside the weather-resistant enclosure to protect them from the elements.

NOTE

: Do not remove the back cover of your recorder. There are no user-serviceable

parts and removing the cover will void your warranty. When necessary, only remove

the thumb-screw cover for the memory bay, the two twist-off battery bay covers, and

the four connector module caps.

Each of the four connectors provides a weatherproof seal when mated with a

microphone cable or with the watertight connector caps. Connector caps protect

the connector port from moisture and debris. Always cap unused connectors.

Push a cap over each exposed connector until fully seated and secure.

CAUTION

: Gently, but firmly, hand-tighten all covers, caps, and connectors to

completely secure the device against the environment before use. Do not use tools or

apply too much pressure since over-tightening could damage the recorder.

Summary of Contents for sm3bat























































































Search results

Summary of Contents for sm3bat

Reviews:

Related manuals for sm3bat

Brands by name

Popular brands

Wildlife Acoustics sm3bat, User Manual

Search results

Summary of Contents for sm3bat

Reviews:

Related manuals for sm3bat

Brands by name

Popular brands