Whirlpool M-17 Technical Manual Download Page 85

Page: 85 / 88

COMPONENT ACCESS (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

4-21

Removing Sump and Motor Assembly - GWS Model

Unplug dishwasher or disconnect power.

Complete the steps

1-4

from

"Drip Pan and Float Assembly"

section.

Complete the steps

1-7

from

"Removing Lower Spray Arm

and Manifold Assembly"

section.

Remove four TORX T15 screws to sump.

Disconnect water supply under sink if necessary.

Disconnect drain hose under sink if necessary.

Disconnect electrical under sink or at junction box if needed.

Pull dishwasher out from under the counter and lay it on it's

back.

Cut the hose clamp crimp to remove the hose to the sump.

NOTE:

For reconnecting the hoses, re-crimp a new

replacement clamp in the positions shown in the figure.

10.

Press in both sides of the TPA to remove the connector from

the housing. Pull the TPA out of secured position and remove.

Motor Assembly GWS Model

11.

Push to release the tab and pull up the connector to remove

from the housing.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands