Whirlpool M-17 Technical Manual Download Page 14

Page: 14 / 88

GENERAL INFORMATION (Cont.)

1-10

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Product Specifications

Whirlpool

Large Capacity Dishwasher with Third Level Rack

KitchenAid

39 dBA Dishwasher with Third Level Utensil Rack

Maytag

Stainless Steel Tub Dishwasher with Dual Power Filtration

Dimensions

Depth Closed Excluding Handles (IN, inches)

or 26

Depth Closed Including Handles (IN, inches)

or 26

Depth With Door Open 90 Degree (IN, inches)

or 51

Depth (IN, inches)

or 26

Height (IN, inches)

Maximum Height (IN, inches)

or 34

Minimum Height (IN, inches)

or 33

Width (IN, inches)

Number of Place Settings

13 or 14

Description

Dishwasher Type

Built-In

Controls

Automatic Temperature Controls

Yes

Control Location

Front or Hidden Top

Control Type

Tap Touch with Display or Electronic Touch with Display

End of Cycle Signal

Yes

Sensor

Yes

Status Light

White

Exterior

Control Panel Color

Gray or Black

Door Style

Flat

Handle Color

Gray or Stainless Steel or Black or White

Handle Material

Plastic or Metal

Handle Type

Long Pocket or Towel Bar

Magnetic Door

Yes

Toe Panel Color

Black or White

True Hold Door

Yes

Features

Decibel Level (dBA) (Whirlpool® Models Only)

41 or 47

Decibel Level (dBA) (KitchenAid® Models Only)

Decibel Level (dBA) (Maytag® Models Only)

Dispensers

Detergent and Rinse Aid

Number of Wash Levels

Rinse Aid Dispenser Level Indicator

Yes

Sound Package

Yes

Cycles and Options (Whirlpool® Models Only)

Dishwasher Cycle Selections

Heavy, Normal, Quick Wash, Sensor Wash, Soak & Clean

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands