Whirlpool M-17 Technical Manual Download Page 67

Page: 67 / 88

COMPONENT ACCESS (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

4-3

Siphon Break

Tools Needed:

Oil filter wrench

90 degree bent nose pliers

Locate siphon break nut inside tub back lower left corner.

Use oil filter wrench or bent nose pliers to loosen siphon

break nut inside tube by turning it counterclockwise.

Disconnect water inlet hose. Using pliers, squeeze water inlet

clamp and pull hose away from siphon break.

Disconnect drain pump hose. Remove black plastic C-clamp

securing drain pump hose to siphon break and pull hose

down and away from siphon break assembly.

Disconnect drain pump output hose. Using pliers, squeeze

drain hose output clamp and pull down on hose away from

siphon break assembly.

Using pliers squeeze plastic retainer together and pull siphon

break assembly out and up to remove.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

A B

A. Siphon Break Assembly

B. Clamp

C. Water Inlet Hose

A. Siphon Break Assembly

B. C-Clamp

C. Drain Pump Hose

A. Siphon Break Assembly

B. Clamp

C. Drain Pump Output Hose

A. Plastic Retainer

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands