Whirlpool M-17 Technical Manual Download Page 60

Page: 60 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

3-22

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

DC Fan Motor

This test will check the wiring to the DC fan motor and the fan

motor itself. The following items are part of the DC Fan Motor

circuit:

Harness/Connection

DC Fan Motor

Control Board

Test Procedure

Check for fan operation in the Diagnostics Cycle. The DC fan

should be running during step 4.

Unplug dishwasher or disconnect power.

Remove toe and outer door panels to access control board.

Strip Circuit -DC Fan Motor

Unplug connector P14 from control board.

Check the fan motor using an ohmmeter, measure the

resistance between P14-1 and P14-2.

If the resistance is between 145k-185k ohms, the fan

motor and harness are good. Go to step 7.

If outside the range, replace the fan motor assembly.

If an open circuit is detected, check connections and

harness continuity between control and fan motor. If

good, replace the fan motor assembly.

Reconnect P14 to control board.

Set voltmeter to DC and connect leads to test-pads

P14- 1 and P14-2 on the control board. Plug in dishwasher or

reconnect power.

Start the Diagnostics Cycle and at the proper interval

measure for DC out of the control board between P14-1 and

P14-2 (Refer to DC Fan Motor Strip Circuit below).

IMPORTANT:

The Fan Motor must be connected to the

control board to measure voltage accurately.

If no DC voltage is measured, replace the control board

and retest.

If 13 VDC ± 5% is measured and the fan is spinning, go to

step 9.

Unplug dishwasher or disconnect power.

10.

Reassemble all parts and panels.

11.

Plug in dishwasher or reconnect power and run Diagnostics

Cycle to verify repair.

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Electronic Control

P14-1

Electronic Control

P14-2

Ref

13 VDC

Pin 1

Pin 3

Fan Motor

13 V / 1 W

145 - 185 kΩ

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands