Whirlpool M-17 Technical Manual Download Page 82

Page: 82 / 88

COMPONENT ACCESS (Cont.)

4-18

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Removing Sump and Motor Assembly (Continued)

Disconnect water supply under sink if necessary.

Disconnect drain hose under sink if necessary.

Disconnect electrical under sink or at junction box if needed.

Pull dishwasher out from under the counter and lay it on it's

back.

Move junction box out of the way by twisting up on left side

and pulling it up and away from the retaining bar.

10.

To remove plastic drain pump bracket, use a standard

screwdriver to push down on tab and push bracket away from

you.

11.

Remove black plastic hose retainer and disconnect drain hose

from drain pump port.

12.

Complete the steps

1-6

from

"Removing Drain Pump"

section.

13.

Remove plastic screw/plug on the right side of the motor

bracket using a Phillips screwdriver.

A
B
C

A. Drain Pump Port

B. Plastic Hose Retainer

D. Drain Pump Hose

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands