Whirlpool M-17 Technical Manual Download Page 51

Page: 51 / 88

For Service Technician Use Only

COMPONENT TESTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

3-13

Water Sensing with the OWI Sensor

This test will check the wiring to the OWI (Optical Water

Indicator), which incorporates the temperature thermistor and

the foam and turbidity sensor. The following items are part of the

water sensing circuit:

Harness/Connection

OWI Sensor

Control Board

Test Procedure

Check the operation of the OWI Sensor in the Service

Diagnostics Cycle.

Unplug dishwasher or disconnect power.

Remove toe and access panels to access control board.

Disconnect P10 from the Control Board.

Using an ohmmeter, measure resistance between P10, pins

1 and 3. The following table provides approximate room

and hot water temperatures and their associated resistance

values.

Temp °C (°F)

RES Range kΩ (ohms)

20 (68)

57.3 - 60.3

25 (77)

45.9 - 48.1

30 (86)

37.0 - 38.7

35 (95)

30.1 - 31.3

Temp °C (°F)

RES Range kΩ (ohms)

40 (104)

24.6 - 25.4

45 (113)

20.2 - 20.8

50 (122)

16.7 - 17.1

55 (131)

13.9 - 14.2

60 (140)

11.6 - 11.8

65 (149)

9.7 - 9.9

70 (158)

8.2 - 8.4

NOTE:

All thermistor resistance measurements must be made

while dishwasher is unplugged or disconnected from power and

connector P10 removed from control.

If the thermistor resistance is OK , the thermistor is good.

Go to step 6.

If the thermistor resistance does not agree with the table,

replace the OWI Sensor.

If an open circuit is detected, check connections and

harness continuity between control and OWI. If good,

replace the OWI Sensor.

Using an ohmmeter, check P10 -1 to cabinet ground and

P10-3 to cabinet ground.

If no short is indicated, go to step 7.

If either pin indicates continuity to ground (short), repair

or replace wiring harness and retest.

Reconnect P10 to control board.

Test for 5 VDC with a voltmeter set to DC, connect the black

lead to P10-2 and the red lead to P10-3.

Plug in dishwasher or reconnect power.

10.

Start the Diagnostics Cycle and at the proper interval

measure for 5 VDC out of the control board between P10-2

and P10-3.

If 5 VDC is measured the control is functioning, go to

step 11.

If no DC voltage is measured, replace the control board

and retest.

11.

Unplug dishwasher or disconnect power.

12.

Reassemble all parts and panels.

13.

Plug in dishwasher or reconnect power and run Diagnostics

Cycle to verify repair.

Strip Circuit - Water Sensing

DANGER

Electrical Shock Hazard

Only authorized technicians should perform

diagnostic voltage measurements.
After performing voltage measurements,

disconnect power before servicing.
Failure to follow these instructions can result in

death or electrical shock.

Electronic

Control

P10-6

P10-5
P10-4
P10-3

P10-2

P10-1

Pin 1
Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Measure NTC resistance at P10-1 and

P10-3 connector disconnected from control.

Turbidity Drive

Unused

OPT Sig

VCC

Ref

NTC

OWI Sensor

Temperature: NTC Thermistor

45.9 KΩ - 48.1 KΩ at 77°F (25°C)

11.6 KΩ - 11.8 KΩ at 140°F (60°C)

YL
YL

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Whirlpool M-17, Technical Manual, Page: 51 / 88

Search results

Summary of Contents for M-17

Reviews: