Whirlpool M-17 Technical Manual Download Page 70

Page: 70 / 88

COMPONENT ACCESS (Cont.)

4-6

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Removing the Inner Door and Hinges

Removing the Inner Door

Unplug dishwasher or disconnect power.

Complete the step

1-4

from

"Remove Outer Door Panel"

section.

Open the inner door slightly and insert 7/64" drill bits (or

Allen wrench's) into hinge hole as shown in below image:

This will keep the hinge slightly open and make replacing the

inner door easier.

Remove the two TORX T20 screws attaching the inner door

panel to the hinge and repeat for other hinge. Then lift up on

inner door to remove.

Removing the Hinge

Using a 5/16" nut driver remove two rear screws and use

a 1/4" nut driver to remove the front two screws. Repeat the

step for other hinge.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands