Whirlpool M-17 Technical Manual Download Page 68

Page: 68 / 88

COMPONENT ACCESS (Cont.)

4-4

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Accessing Door Components

Remove Outer Door Panel

Unplug dishwasher or disconnect power.

Using a TORX

†

T15

screwdriver, remove the six short screws

(three on each side) and three long as shown in below image:

NOTE:

Leave the (short) screw to the left of the door latch in

place as this screw secures the door latch to the door.

Lift the outer door assembly up and away with enough room

to disconnect the ACU harness and clip. Unclip the harness

from the harness retaining clip.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

†®

Torx T15 and T20 are trademarks of Acument Intellectual Properties, LLC.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands