Whirlpool M-17 Technical Manual Download Page 86

Page: 86 / 88

COMPONENT ACCESS

4-22

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Removing Sump and Motor Assembly - GWS Model (Continued)

12.

Using a small Phillips screwdriver, turn counterclockwise to

remove plastic screw which is securing the locator/motor

bracket.

13.

Push locator away from grommet center to remove.

14.

Remove the motor assembly.

Sump Assembly GWS Model
15.

Unclip harness from the sump. Remove thermostat and

disconnect wire harness connectors to diverter motor and

wash motor.

16.

Remove OWI by turning in counterclockwise a quarter turn.

17.

Slide sump assembly to the left along the rear bracket. Lift up

on the left side of the assembly and pull it up and away from

the rear bracket.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands