Whirlpool M-17 Technical Manual Download Page 27

Page: 27 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

2-7

FUNCTION CODE ERROR CODE

CAUSES

WHAT TO CHECK

8 - Inlet Water

3 - Suds / air in

pump

Too many suds

1. Start a cycle, allow unit to fill and wash for

1-2 minutes. Open door and check for excessive

sudsing.

2. Confirm using proper dishwasher detergent, not

hand detergent.

3. Check for excessive rinse aid leakage. Disconnect

power and replace dispenser if rinse aid is leaking.

Bowls or pots loaded or flipped upside

down and captured wash water

Instruct customer on loading. Refer to

Owner's

Manual

Water leaking from dishwasher

Check for leaks under dishwasher.

Diverter disk in sump missing

Remove lower spray arm, rear feedtube, and outlet

cover and verify whether the diverter disk is installed.

4 - Overfill

switch open

Overfill switch unplugged

Remove access panel and inspect overfill switch

assembly. Ensure connector is fully seated.

Water in leak pan under unit

Remove access panel and check for water in leak

pan. If water present, unplug float switch, remove

pan and empty it. Replace pan and reconnect the

switch. Press Cancel key twice to remove unit from

error mode. Verify that fault code is not re-detected

by control.

NOTE:

Root cause of overfill must be corrected or

customer will experience another overfill and service

call in the future.

Overfill switch stuck in open/up

position

1. Remove access panel and inspect overfill switch

assembly and pan for water or obstruction. Verify

that Styrofoam float is able to move freely and you

hear the "click" of switch contacts when it is down.

2. Unplug dishwasher or disconnect power and check

resistance of overfill switch. Switch should be

shorted when float is down.

Drain issue

Check other fault codes to see if F9E1 and/or F9E2

have been recorded. See info for these fault codes

below.

Fill valve mechanically stuck open

Check other fault codes to see if F8E5 is also

recorded. See info for F8E5 below.

Fill valve TRIAC on control shorted

Check other fault codes to see if F1E1 is also

recorded. See info for F1E1 above.

Unit not level and water surges down

overfill funnels into leak pan during

cycle

Check levelness of dishwasher. If unit is tilted

forward, water is more likely to enter funnels and fill

leak pan. Adjust unit until level. Empty leak pan.

Air pressure surges when door is

opened and immediately closed while

dishwasher is hot can force water

droplets down funnels into leak pan.

Instruct customer to leave dishwasher open a few

minutes if door is opened when unit is hot. Empty

leak pan.

Too many suds

1. Start a cycle, allow unit to fill and wash for

1-2 minutes. Open door and check for excessive

sudsing.

2. Confirm using proper dishwasher detergent, not

hand detergent.

3. Check for excessive rinse aid leakage. Disconnect

power and replace dispenser if rinse aid is leaking.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands