Whirlpool M-17 Technical Manual Download Page 18

Page: 18 / 88

GENERAL INFORMATION (Cont.)

1-14

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Product Features (Continued)

KitchenAid

Cycle Guide

CYCLE

Control

Purpose

ProWash

Senses soil to automatically optimize cycle. ProWash™ cycle is selected if START is pressed first.

Tough

Use for hard to clean items.

Normal

This cycle is recommended for daily, regular or typical use to completely wash and dry a full load of normally

soiled dishes.

Light

Use for lightly soiled items like china and crystal.

Express Wash

Use when you need faster results.

Rinse Only

Use for rinsing dishes, glasses, and silverware that will not be washed right away. Do not use detergent.

OPTIONS

Control

Purpose

Hi Temp Wash

Helps remove tough, baked on food.

Sani Rinse

Sanitizes dishes and glassware in accordance with NSF International NSF/ANSI Standard 184 for Residential

Dishwashers. See this section in the Owner’s Manual.

Heat Dry

Dries dishes with heat. Load plastic item in upper racks.

Extended Heat Dry

Increases the Energy used for drying the dishes. This may lengthen the cycle time.

Delay

Runs the dishwasher at a later time.

ProDry

Dries dishes with heat and a fan. Use for best performance.

Top 2 Racks

Wash items in the Top two racks only. Only a limited amount of water will be sent to the lower spray arm.

Start / Resume

Push to start or resume a cycle.

Cancel / Drain

Push to reset any cycle or options during selection. Push to end a cycle once started.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands