Whirlpool M-17 Technical Manual Download Page 72

Page: 72 / 88

COMPONENT ACCESS (Cont.)

4-8

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

Removing User Interface and Door Latch

Removing the User Interface

Unplug dishwasher or disconnect power.

Complete the step

1-6

from

"ProDry

™

Assembly"

section.

Use a TORX T15 screwdriver to remove the three (3) screws

securing the UI to the outer door panel.

NOTE:

The light pipe is not removed during UI replacement. It

remains attached to the outer door panel.

Remove Latch Assembly

Use a TORX T15 screwdriver to remove the one screw

attaching the Latch Assembly to the door panel.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands