Whirlpool M-17 Technical Manual Download Page 71

Page: 71 / 88

COMPONENT ACCESS (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

4-7

ProDry™ Assembly

Tools Needed:

90 degree bent nose pliers

Complete the step

1-4

from

"Remove the Inner Door"

section.

Using 90 degree bent nose pliers turn the ProDry™ vent

counterclockwise to loosen and remove.

The ProDry™ assembly can now be removed.

Disconnect wax motor connector by pressing down on tab

and lifting up on harness connector.

Remove fan harness by pushing down on tab and lifting up on

harness. Refer the below image.

To remove vent assembly, use a screwdriver to push in on tab

shown and pull vent away from wax motor.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands