Whirlpool M-17 Technical Manual Download Page 37

Page: 37 / 88

For Service Technician Use Only

DIAGNOSTICS AND TROUBLESHOOTING (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

2-17

Troubleshooting Guide (Continued)

CUSTOMER DESCRIPTION

POTENTIAL CAUSES

CHECK

RELATED

ERROR

CODES

Noisy operation

Open fuse on control to vent wax motor Refer to “Fuse Service and Resistance

Check” in section 3.

Vent drive circuit on control failed

Unplug dishwasher or disconnect power

and check resistances of vent wax motor

and all connections in vent circuit. Fix/

replace open connections/part.

Fan runs (makes noise) after cycle

complete (On models with fan)

Dishwasher is designed to keep fan

running after cycle to prevent moisture

build up in dishwasher. Fan will turn off

if door opened longer than 5 seconds.

Instruct customer.

Excessive fan noise due to faulty fan

motor (On models with fan)

1. Check fan operation during Service

cycle.

2. Unplug dishwasher or disconnect

power.

3. Check resistances of fan motor and all

connections in fan circuit. Fix/replace

open connections/part.

Leaks or drips on cabinet or

floor

Loose connection in vent circuit and/or

open vent wax motor

Unplug dishwasher or disconnect power

and check resistances of vent wax motor

and all connections in vent circuit. Fix/

replace open connections/part.

F10E2 (FAE2)

Open fuse on control to vent wax motor Refer to “Fuse Service and Resistance

Check” in section 3.

Vent drive circuit on control failed

Unplug dishwasher or disconnect power

and check resistances of vent wax motor

and all connections in vent circuit. Fix/

replace open connections/part.

Fan problem

Refer to “

Service Error Codes

” table.

F10E3 (FAE3)

Too many suds

Refer to “

Service Error Codes

” table.

F8E3

Leaking dishwasher

Check door/tub gasket and all water

connections below dishwasher. Refer to

“

Service Error Codes

” table.

F8E4

Unit not level and water surges over

front tub lip or down overfill funnels

during cycle

Check levelness of dishwasher. If unit

is tilted forward, water is more likely to

enter funnels and fill leak pan. Adjust unit

until level. Inspect leak pan and empty if

needed.

F8E4

Air pressure surges when door is

opened and immediately closed while

dishwasher is hot can force water

droplets out vent duct or down funnels

into leak pan.

Instruct customer to leave dishwasher

open a few minutes if door is opened

when unit is hot. Inspect leak pan and

empty if needed.

F8E4

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands