Whirlpool M-17 Technical Manual Download Page 79

Page: 79 / 88

COMPONENT ACCESS (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

4-15

Removing Heater Assembly

Unplug dishwasher or disconnect power.

Locate the heater terminals at the bottom of the dishwasher.

Disconnect wires from both heater terminals.

Remove both heater element nuts.

Remove heater element assembly from tub.

Removing Drain Pump

Unplug dishwasher or disconnect power.

Uninstall dishwasher so that it can be pulled half way out of

cabinet.

Turn off water supply to dishwasher. Disconnect drain hose if

necessary. Unscrew anchors to cabinet.

Locate the drain pump in the lower front right of dishwasher.

Push in on tab and turn drain pump 1/4 turn

counterclockwise to remove.

Remove plastic wire harness connector retainer by pulling it

straight out. Push in on connector retainer and remove

harness.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

A. Heater Element Assembly

B. Heater Washer

C. Heater Element Nut

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands