Whirlpool M-17 Technical Manual Download Page 81

Page: 81 / 88

COMPONENT ACCESS (Cont.)

Whirlpool

and KitchenAid

Filtration and Maytag

24" Microfiltration Dishwashers

4-17

Drip Pan and Float Assembly

Remove Drip Pan and Float Assembly

Remove toe/access panel using a 5/16" nut driver.

To remove the drip pan assembly, press the snap at each side

of the plastic tray in toward the center of the product and

pull toward yourself.

NOTE:

Take caution not to pull too far or too hard as the float

switch wire is still connected at this time.

Remove Float Switch Wire

To remove the float switch wire, gently depress the connector

latch tab and then pull the connector out of the housing. To

remove the float push in on the two tabs and lift up on the

float.

Removing Sump and Motor

Assembly

Unplug dishwasher or disconnect power.

Complete the steps

1-4

from

"Drip Pan and Float Assembly"

section.

Complete the steps

1-7

from

"Removing Lower Spray Arm

and Manifold Assembly"

section.

Remove four (4) TORX T15 screws to sump.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Failure to do so can result in death or

electrical shock.

Replace all parts and panels before operating.

Summary of Contents for M-17

























































































Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands

Whirlpool M-17, Technical Manual

Search results

Summary of Contents for M-17

Reviews:

Related manuals for M-17

Brands by name

Popular brands