manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Installation And Operating Instruction

The Weishaupt WTC-GB 15-B Compact is a high-quality heating system that ensures optimal comfort in any space. To easily set up and operate this product, download the free "Installation and Operating Instruction" manual from our website manualshive.com. It provides in-depth guidance for a hassle-free experience.

Share
Download
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

6 Operation

83309302 1/2018-05 La

65-196

6.6.1 Info

In menu Info, the information is read only.

6.6.1.1 System

Info

 

 

System

Information

Description

1.1.1
Status

Current operating mode of system.

The operating mode is determined from the operating mode of the system and the
operating modes of the individual heating circuits.

Off
Standby
Summer
Automatic

1.1.2
External temperature

Current temperature at the external sensor (B1).

Show additional information:

Press dial knob.

Current

:

Current external temperature used for system frost protection.

Damped

:

Tendency of the outdoor temperature used for the summer-winter changeover.

Mixed

:

Calculated outdoor temperature (current and damped) used for the flow setpoint
temperature.

1.1.3
Heat demand
Heating

Required maximum flow setpoint temperature of all heating circuits.

1.1.4 … 1.1.27
Heat demand
Heating circuit …

Required flow setpoint temperature of the corresponding heating circuit.

1.1.28
Heat demand
DHW

Required flow setpoint temperature of the DHW circuit.

Summary of Contents for WTC-GB 15-B Compact





































































































































































































Reviews:

No comments

Related manuals for WTC-GB 15-B Compact

Watson Marlow Pumps 630 Series Installation, Operating And Maintenance Manual preview
630 Series
Brand: Watson Marlow Pumps Pages: 131
Eaton 2 Series Parts & Repair Information preview
2 Series
Brand: Eaton Pages: 57
Samsung MIM-E03CN Installation And Maintenance Manual preview
MIM-E03CN
Brand: Samsung Pages: 27
KASTOR K Series Installation And Operating Instructions Manual preview
K Series
Brand: KASTOR Pages: 40
VARISCO K Series Instructions For Use And Maintenance Manual preview
K Series
Brand: VARISCO Pages: 52
Raypak 5350 Series Installation And Operating Instructions Manual preview
5350 Series
Brand: Raypak Pages: 60
Caframo Pali 9510CA-BBX Operating Instructions preview
Pali 9510CA-BBX
Brand: Caframo Pages: 5
Daikin VRV IV+ Installation And Operation Manual preview
VRV IV+
Brand: Daikin Pages: 52
Daikin FVXG25K2V1B Service Manual preview
FVXG25K2V1B
Brand: Daikin Pages: 147
Daikin CTXU25G2V1B Service Manual preview
CTXU25G2V1B
Brand: Daikin Pages: 175
Danfoss iSave 40 Service Manual preview
iSave 40
Brand: Danfoss Pages: 26
Calpeda GX Series Original Operating Instructions preview
GX Series
Brand: Calpeda Pages: 80
Danfoss DHP-AT User Manual preview
DHP-AT
Brand: Danfoss Pages: 24
Warmco XR Series Instruction Manual preview
XR Series
Brand: Warmco Pages: 25
Amana PTH123G Manual preview
PTH123G
Brand: Amana Pages: 26
ubbink Smartmax Series Manual preview
Smartmax Series
Brand: ubbink Pages: 29
Bartec BACAB FT Installation Instructions Manual preview
BACAB FT
Brand: Bartec Pages: 24
SPERONI SDC 200 Operating Instructions Manual preview
SDC 200
Brand: SPERONI Pages: 68

Brands by name

Popular brands

Load more brands